小区或者工厂等地使用的道闸，标准的配置是遥控开启的，也就是出厂标配两个遥控手柄，当有车辆需要进出时，管理者通过遥控器或者外接的台控来升起或者落下道闸杆。


he standard configuration of lane gates used in residential areas or factories is remote control, that is to say, two remote control handles are allocated to the factory. When a vehicle needs to enter or leave, the manager lifts or drops the lane gates through the remote control or external control.


这当然是做简单，也是比较实用的一种管理方式，不过为了让通道管理更加轻松，便捷，厂家也开发了越来越多，更加智能，方便，安全的管理方式。


This is of course a simple and practical way of management, but in order to make the channel management easier and more convenient, manufacturers have developed more and more intelligent, convenient and safe management methods.


比如，地磁感应，蓝牙，车牌识别等


For example, geomagnetic induction, Bluetooth, license plate recognition, etc.


「哈尔滨道闸」小区挡车器预埋地感线圈的方法


The Method of Embedding Ground Inductance Coil in Block of Harbin Road Gate


为了道闸的车辆检测器工作在状下，地感线圈的安装极为重要，下面我们了解一下道闸地感线圈的安装，为了使检测器工作在状态下，线圈的电感量应保持在100uH－300uH之间。


In order to make the vehicle detector work in the optimum condition, the installation of the ground inductance coil is very important. Now let's understａnd the installation of the ground inductance coil. In order to make the detector work in the optimum condition, the inductance of the coil should be kept between 100uH and 300uH.



在线圈电感不变的情况下，线圈的匝数与周长有着重要关系。


When the inductance of the coil is constant, the number of turns of the coil has an important relationship with the circumference.


周长越小，匝数就越多。


The smaller the circumference, the more turns.


由于道路下可能埋设有各种电缆管线、钢筋、下水道盖等金属物质，这些都会对线圈的实际电感值产生很大影响，所以在实际施工时用户应使用电感测试仪实际测试电感线圈的电感值来确定施工的实际匝数，只要保证线圈的最终电感值在合理的工作范围之内(如在100uH—300uH之间)。


Because there may be various kinds of metal materials buried under the road, such as cable pipelines, reinforcing bars, sewer covers and so on, which will have a great impact on the actual inductance value of the coil, users should use inductance tester to test the inductance value of the inductance coil to determine the actual number of turns in the construction, as long as the final inductance value of the coil is within a reasonable working range (such as 100). Between uH and 300uH.
　　

在绕制线圈时，要留出足够长度的导线以便连接到环路感应器，又能保证中间没有接头。绕好线圈电缆以后，必须将引出电缆做成紧密双绞的形式，要求最少1米绞合20次。


When winding the coil, it is necessary to leave enough length of wire to connect to the loop inductor and ensure that there is no joint in the middle. After winding the coil cable, the lead-out cable must be made into a tight twisted pair, requiring at least one meter to be twisted 20 times.


否则，未双绞的输出引线将会引入干拢，使线圈电感值变得不稳定。


Otherwise, the output leads without twisted pairs will be introduced to dry up, which will make the inductance value of the coil unstable.




输出引线长度一般不应超过5米。


The length of output lead should not exceed 5 meters in general.


由于探测线圈的灵敏度随引线长度的增加而降低，所以引线电缆的长度要尽可能短。


Because the sensitivity of detection coil decreases with the increase of lead length, the length of lead cable should be as short as possible.

　　
线圈埋设首先要用切路机在路面上切出槽来。


Coil embedding should first use road cutter to cut grooves on the road surface.


在四个角上进行45度倒角，防止尖角破坏线圈电缆。


Carry out 45 degree chamfering on the four corners to prevent the sharp corners from damaging the coil cable.


切槽宽度一般为4到8毫米，深度30到50毫米。同时还要为线圈引线切一条通到路边的槽。


Slot width is generally 4 to 8 mm and depth is 30 to 50 mm. At the same time, cut a slot to the roadside for the coil lead.


但要注意：切槽内必须清洁无水或其它液体渗入。


However, it should be noted that the groove must be clean, anhydrous or other liquid infiltration.


绕线圈时必须将线圈拉直，但不要绷得太紧并紧贴槽底。将线圈绕好后，将双绞好的输出引线通过引出线槽引出。


When winding the coil, the coil must be straightened, but not too tight and close to the bottom of the groove. After winding the coil, the output lead of the twisted pair is drawn through the lead slot.


在线圈的绕制过程中，应使用电感测试仪实际测试电感线圈的电感值，并确保线圈的电感值在在100uH—300uH之间。


In the winding process of coil, the inductance value of inductance coil should be measured by inductance tester, and the inductance value of coil should be between 100uH and 300uH.


否则，应对线圈的匝数进行调整。


Otherwise, the turn number of the coil should be adjusted.


哈尔滨创隆科技是一家道闸年产销量超过10万的生产厂家，道闸是我公司经过精心设计并制作的一款能够适应现代“安全、快捷、高效、高质”管理的新一代的数字道闸；


Harbin Chuanglong Technology is a manufacturer with annual production and sales of more than 100,000 sluices. The sluices are a new generation of digital sluices designed and manufactured by our company, which can adapt to modern "safe, fast, efficient and high quality" management.


其高标准、高质量、高集成化的特性，时尚潮流的外观形象，及其独特地颜色视觉魅力，给人一种尊贵高雅、爽心悦目的感觉，是停车场，酒店，学校，花园别墅小区，企事业单位等场合的配套。


Its high standard, high quality, high integration characteristics, fashion trend appearance, and its unique color visual charm give people a noble, elegant, refreshing and pleasant feeling, is the first choice for parking, hotels, schools, garden villas, enterprises and institutions and other occasions.