A． 电控系统 

采用日道PLC电子控制系统及变频器，一体化控制，功能完善，适应性强、功耗低。采用集成电路无触点控制，可根据自身工艺要求随意更改系统控制程序。

Fully Automatic Electric-control System

adopt Nippon PLC Electric-control system and inverter, It features in incorporate control, perfect funciton, stong adaptabillty, and low power consumption. It adopts non-contactcontrol by in tegrated circuirt, which can freely alter the systematic controlling program me according to the requirements of its techics.

B．飞达座

采用印刷机的飞达头设计，加强型的送纸装置，吸纸准确，送纸平滑顺畅，配备连续叠纸系统，高效运转要求。

Feeder base

It adopts HMA printer with feeder head design, stengthen type feeding device, which ensures a accurate paper adsorbing and a smooth paper feeding. It is equipped with constant paper-piling system, which ca fully satisfy the requirement of high efficient operation.

C．底纸送纸部

采用吸风皮带送纸及伺服马达驱动，分别对应A/B/E浪三层，五层瓦楞底纸及卡、板底纸，输送准确顺畅。

Substrate Paper Feeding Section

Adopt air-absorbing belt to feed the paper driven by motor, which corresponds to A/B/Eflute three-layer, five-aayer corrugated paper and cardboard and substrate board paper and ensure an accurate andsmooth feeding.

D．微调调整器

日产原装微动相位调整器，配合正时对位系统，可于机械高速工作时调整贴合误差而无需停机。

Micro-tuning Regulator

Original Nippon micro-tuningphase regulator is combined sith timing para system; It can adjust the sticking error in the Non-stop state when the machine works in high speed. 

E．传动系统

以进口时规皮带替代传统齿轮链条，解决因金属链条磨损而造成面底纸贴合不准之问题。

Transmission system

Replace the traditional gear chain with imported timing belt, which can perfectly solve the problems ofinaccurate sticking problem aroused from metal chain abrasion.

F．齐纸正时部

采用同步后推进式档规，面底档规同步推动面纸及底纸进入贴合部，并可不停机微调面底纸之贴合精度。

Paper Triming andTiming Section

Adopt the synchronous pushing mode rollers, substrate & litho rollerswill push synchro-nously the litho paper and substrate paper into the sticking section, and adjust the gluing precision between litho andsubstrate paper by micro tuning in the non-stop state.

G．胶水涂布系统

全自动胶水补充装置，配合胶水流失回收循环，避免胶水浪费。依产品要求，可调整胶水厚度控制轮，配合特殊花纹胶辊，有效解决涂布甩糊问题并节省胶水消耗。

Glue coating system

Automatic glue-adding device is combined with a run-off glue recycling system, which can avoid waste of glue. According to the requirement, the controlling wheel can be adjusted for control of glue thikness and can be equipped with special embossing glue roller, which efficentlysove the problems of swing and pasting during coatingand save the consumption of  glue.

l          调换不同规格产品只需时约6-10分钟，更适合短单产品；

l          可在高速工作时调整贴合误差而无需停机；

l          面纸配置双重上面纸结构，堆纸高度达1.8米，预叠式送纸更节约时间；

l          底纸吸风装置采用中心向外扩张，更适应不同规格底纸，令送纸更加顺畅；

l          给纸采用电磁制动系统，异常刹车停止时，无惯性转动，不浪费纸张；

l          面纸及底纸采用同步光电控制技术，避免底纸或面纸不到位的问题；

l          所有电控，时规皮带、电机均采用日本、美国、中国台湾元口器件。

l          Size changeover needs only 6-10min, so more suitable for short and single product;

l          Adjustment of joint error is available when running at high speed without stop-press;

l          Double upper surface paper structure; stacking paper up to 1.8m; pre-folded feeding mode to save time more;

l          Bottom paper indraught device operates in the way from center to the outside to adapt to different sizes, so paper is fed smoothly more;

l          Feeding adopts electromagnetic braking system; when abnormal stoop, no inertial rotation exists to avoid paper waste;

l          Surface and bottom paper adopt synchronous photoelectric control technology to avoid unreachable bottom paper or surface paper;

l          All electrically-controlled bolts and motors adopt elements and components made in Japan, USA and Taiwan.