美国福禄克 Fluke 700 HTH 液压测试管压力校准器-苏州圣光仪器有限公司

美国福禄克Fluke 700 HTH液压测试管

配合使用：与Fluke 700HTP液压测试泵配合使用。
描述：
● 压力高达10，000Mpa
● 长1米
随机附件包括：
● 不锈钢接头接700HTP手泵
● 不锈钢接头接仪表
● 复合密封圈
● 尼龙密封圈
● 接头： 1/4NPT外螺纹到1/4NTP外螺纹，1/4NPT外螺纹到1/8NTP外螺纹
● 操作指南

美国福禄克Fluke 700 PCK压力校准套件
描述：Fluke 700PCK使那些自己有**压力标准的用户可以自己来校准其压力模块
Fluke 700 ILFN内嵌式过滤器
配合使用：与Fluke713，717，718压力校准器配合使用。
描述：使校准器的传感器与液体隔离，它可以吸收气体中少量的小滴液体。
● 入口接头：1/8NPT黄铜内螺纹接头
● 出口接头：1/8NPT黄铜内螺纹接头
● *高压力量程：100psi/690vkPa
● 爆破压力：375psi/2588kPa
● *高温度：200°F/93℃
应用：Fluke-718只可以使用干的非腐蚀性的气体，接一个Fluke-700ILF在718的压力接口将会控制液体进入校准器，这样就可以使718可以应用在压力输出源并不是干的场合，当发现气体中有明显的水珠或过滤器被大量的液体浸透时应该立即替换过滤器

Fluke 700HTP Hydraulic Test Pump

The Fluke 700HTP is designed to generate pressures up to 10,000 psi/700 bar. The Fluke 700HTP has two pressure ports:
3/8-BSP (ISO228) female parallel thread fitting for the reference gauge or pressure module
1/8-BSP (ISO228) female parallel thread fitting for the unit under test

Note: The user must provide a hose with appropriate end fittings from this port to the unit under test.

Fluke 700HTP Hydraulic Test Pump

This pump can provide up to 10,000 psi using distilled water or mineral-based hydraulic oil. The pump is operated by pumping several strokes to prime the system, then switching to high pressure mode when the resistance increases. An integral pressure adjustment vernier knob varies the pressurized volume by 0.6 cc. The pressure variation achievable with the vernier will depend on the nominal pressure and total pressurized volume, but with a minimum volume, the vernier provided 150-3,000 psi (at 150 psi nominal) and 3,000-10,000 psi (at 3,000 psi nominal) adjustment ranges. With a minimum volume and no pressure applied, the vernier can also be used to provide a 0 to 1.7 psi range. Larger volumes will provide a smaller range of adjustment, but greater resolution.
Included:

Adapter to connect the reference gauge port on the pump body to the 1/4 NPT male fitting on Fluke 700Pxx Pressure Modules (except 700P29, P30, and P31)
Adapter to connect the reference gauge port on the pump body to the 1/4 NPT female fitting on the Fluke 700P29, P30, and P31 Pressure Modules
Adapter to convert the unit under test port to a 1/4 NPT female
Replacement seal kit
Instruction sheet